top of page
 

TAKET  SUPERTWEETERS

 

 

Air Motion Transformer Super Tweeter by TakeT! 

The TakeT “Heil-based” AMT Super tweeters are an astonishing add-on to any system. Notably you will get a huge boost in three dimensionality, you will also get a more palpable midrange and greater density with incredibly more vivid image outlines! You will not get a thinner sound, and no you will not get a brighter sound, on the contrary, you will get a boost in realism and a blacker background.

 
Designed and manufactured in Kanagawa Japan by
Toshitaka Takei
LOGO BACKGROUND FRAME
TAKET LOGO SMALL
TAKET LIVE 3 .jpg
TAKET LIVE Front and Rear.jpg

TAKET LIVE Supertweeter



These Supertweeters are truly transformational and are compatible with all Loudspeakers topologies. 

Minimum Impedance :

200ohms

Reproduction frequency band region :

18kHz -100kHz or more

The maximum output sound efficiency : 100dB/W/m 8 stage switch

Mass :

265 grams

Size :

75mm (width) x 112mm (height) x 100mm (depth with terminals)

Drive system :

Cylindrical TAT-type driver

 

Adjustable SPL efficiency via 8-way switch



$ 1,475.00  / pair

Special Offer $ 1,255.00  - In STOCK !

US Distributor Warranty Included - We are not responsible for Purchases made on E-Bay or Amazon from non-US sellers.

TAKET BEEPURE SUPERTWEETER

 

​TAKET  BEE - PURE   Supertweeter

 



These tiny Supertweeters are housed in an anodized aluminum body. The mebrane which is covered by a stainless steel plate  featuring pinhole arrays to enhance sound diffusion.

 

They are truly transformational, greatly improving #D imagery and frequency extension ant both extremes ! They are compatible with all Loudspeakers topologies. 

 

Maximum V rating :150V

Impedance; : infinity > 4Kohm [DC to 100kHz] 

Reproduction frequency band region : 20kHz -150kHz

The maximum output sound efficiency : 70dB/W/m

Mass : About 140 grams / pc

Size : 60 (width) x 25mm (height) x 56mm (depth with terminals)

Drive system : Polymer Piezo-Electric Heil type

 

 

$450.00  / pair   Special Offer  $ 395.00

TAKET WHDPURE

TAKET WHD-PURE Mid-Bass High Definitioner

 

 

Pure is a name applicable to a product that demonstrates enough tonal quality effect improvement without use of a transformer. The units react directly to the music signal because WHDPURE is transformerless.

 

WHDPURE delivers clear positioning of each part of the music spectrum with exact phase coherence.

Even if the ears do not hear the effect, a wonderful tonal improvement is perceived especially in the bass and the mid-range, albeit at low efficiency.

 

 

Reproduction frequency : 20Hz-15kHz

Efficiency : 50dB/1m*2.83V

Capacitance : 55nF

Impedance; +/-150 ohms (DC-20kHz)

Internal series resistance : 100ohms (2W)

Dimensions : 130mm H x 90mm W x 40mm D  

Mass : About 100 gr

$ 1,375.00  / pair wth Stand     

Special Offer  $ 1,210

 

How do the TAKET Supertweeters affect the sound field ?

 

Please read the explanatory document provided via the link below :

 

Inaudible Frequencies - Effect on the Human Brain ?

Please read the downloadable technical document provided via the link below :

 

NEW PRODUCT DEVELOPMENT

THE SOUNDSTAGE ACTIVATOR

.... what they say ...

 

Dagogo

Constantine Soo | March 2023

What am I hearing ?

First, the slight treble/upper midrange tilt created by the Taket Live is offset by the WHDPURE and leaves the original balance of the main speakers intact. This happens because the WHDPURE somehow supplements the bass and midrange in the same way the Live supplements the overall frequency range. The effect is a very audible improvement in the leading edge, detail, and speed of the musical notes throughout the entire frequency range.

 

Second, the improved dimensionality, spaciousness, detail, and speed that comes from adding the Live is further enhanced by adding the WHDPURE. The effect of using both units together is a very significant increase in the sense of being in the recording/performance venue. It’s clear that the two models were designed to work together.

 

In perusing the TakeT website I couldn’t help but notice the similarity in appearance between the WHDPURE and the TakeT H2+ headphones. To put it bluntly, the H2+ headphones are incredibly clunky looking, and I understand they have a very difficult impedance that requires specialized amplification. However, for purposes of this review, users swear that no other headphone comes close to the bass performance of the H2+. It looks to me like a large subcomponent of the H2+ is based on the fundamental design of the WHDPURE, or vice versa. This suspicion is confirmed by the fact that the WHDPURE instruction manual (in rough English translation) states that “the structure of the TAKET-WHDPURE is different an inside vibration board and the electric circuit, and doesn’t become a headphone though is the same face of TAKET-H2.”

 

So where does this leave us ?

I have several thoughts about these components. One is a comparison to other “add-on” components. For example, I’ve used a Synergistic Research Atmosphere on and off for several years, and its effect has been very minimal, and virtually non-existent with many pieces of music. The TakeT components are way better in creating dimensionality, and improve other aspects to boot. Similarly, I’ve played with dynamic range expanders and equalizers, and they have not come close to the TakeT components’ bang for the buck. YMMV.

 

A second thought I’ve had is how these add-on speakers compare to various tweaks, such as upgrading interconnects or speaker cables. I’m a fan of good cable-matching with specific components, but now I’m wondering if super tweeters wouldn’t have had greater effect than the various cable upgrades I made for comparable dollars. The point is that super tweeters, and in particular the Live/WHDPURE combo, may be a better way to upgrade your system than many other options.

I’m going to see if I can get the Kan Audio Lab TS-001 to compare head-to-head. The Kan is a superlative super tweeter, but my impression is that the combination of the Live and WHDPURE gives you a huge chunk of the Kan’s benefits at a small fraction of the price.

 

Even if a head-to head with the Kan shows that the Kan is clearly superior, the Taket Live and WHDPURE are staying in my main system. Despite the fact that I really don’t understand why they do what they do, they have managed to improve a pretty darn good system assembled over years of careful planning and experimentation. They also clearly improved the two secondary systems in my home, so even if I spent $100,000+ (which I won’t) for new speakers that do what the combined system now does, I will be able to use the TakeT units to upgrade my other systems.

 

Serious Upgrade

The TakeT units also raise the intriguing possibility of seriously upgrading your current main speakers by adding $2,500 worth of add-on speakers. That may make no sense with $1,000 speakers, but if you have $10,000 speakers you should consider spending $15,000-$20,000 to achieve a significant sonic improvement. The Taket-Live and WHDPURE may be just the ticket.

 

Highly recommended. Current pricing is $1,475/pair for the TAKET-LIVE and $1,375 for the WHDPURE at Atelier 13 Audio in Nashville. If you can, I encourage you to buy the two together, which may get you a further deal. Happy listening!

Read the Full Dagogo Review here

 

Customer Observations & Experience 

 

TakeT Batpro2 and Enigmacoustics Sopranino

 

 

BRUCE BISENZ – Sound & Recording Veteran / California

 

https://www.imdb.com/name/nm0083937/
https://magazine.local695.com/magazine/winter-2015/bruce-bisenz

 

Bruce’s System Description

  • 7.1 system. 2 each Sopraninos L/C/R/SS in a specific array to support concert hall ambience.

  • Three mode system: L/R mixing mastering (No Sopraninos), HT and Concert Hall.

  • L/R B&W 802 D3, HTM2 D3 Cntr, 802 D2 rear Surround

  • 2 pair Niles (770/870) side surround(hi mount) in Bi & Monopole

  • 10 AR 1W woofers for L/C/R 50Hz down. Two Paradigm Sub 15s for the .1 Sub channel.

  • Bryston 3X 28B cubed for L/C/R. Two Bryston 4B3 amps for surrounds

  • 2/3 Primare i30/32 receivers to drive Sopraninos

  • Two Burmester 948 power conditioners (each side of the line).

  • Direct to panel 30 Amp 10 Gauge Wire. Extensive additional power support.

  • Datasat RS20i backed up to 4 Weiss DACs.

  • Weiss EQ1 program EQ, Weiss DNA1/K -Stereo Ambiance retrieval.

  • Lot and lots of other goodies including Synergistic Research gear. Audio cables self made :

  • All balanced from unobtanium ‘60s aero space stranded SOLID silver wire Teflon insulation.

  • Nakamichi CT TT with 4 plug in tone arms.

  • Digital RIAA EQ (Weiss EQ1), Weiss ADC2 A to D, and pick up specific EQ.

  • 4/5 Behringer DEQ2496 (digital section only) for ...

  • ... 7.1 program EQ (transition to HT and Concert Hall).

  • Considering adding Sopraninos to rear surround.

     

 

Bruce’s Feedback on Enigmacoustics Sopranino & Taket Barpro2

 

 

Constantin,

 

I previously described the SOP. The BatPro 2 is equally mysterious. It has a largish, apparent, non symmetrical radiation element. It doesn’t recover ambiance like a Sopranino.

 

It beams highs over a distance to provide directionally within a sound Field. It enhances the nature of delicate instruments and voices. Together both units are synergistic.

 

The economics are such that anyone who cannot afford a SOP will enjoy a Bat Pro 2.

However, anyone who can afford a SOP will benefit from the addition of a Bat Pro 2.

 

Indeed, I recommend that you make a package of both BatPro 2 and SOPs as an Atelier 13 “Special.”

(WILL DO) ... Sopranino 2 + BatPro 2 Bundle Price :  $ 2,999 !  (18% off)

 

Also cast about for a description other than “Tweeter” because people think they are going to get some kind of a [slightly better] dome radiator tweeter. So why bother?

(QUITE TRUE)

 

Also describe the effect, not the mechanism because the mechanism appears to the “uninitiated” to be voodoo acoustics. No one, or very few will believe the mechanism.

 

Advertise the result that’s what people are buying. And remember, if it works with my old ears it will work with most anyone.

 

 

Later :

 

Mr. Tweeter, (...Bruce calls me that now :=))

 

As previously described: The Enigmacoustics Sopranino acts in a unique way to recover ambience. It does this by virtue of its broad source (up to 20X the area of a typical dome tweeter) such that there is a wider and more natural image.

 

When properly installed, the sound field envelops and saturates the pinnae. This allows for added realism and grace, even to other than high frequencies. (Pinnae: external part of the ear in humans)

 

When the goal is Opera or Concert Hall realism, then the use of multiple pairs of Sopraninos can establish realistic, enveloping, sound fields which support appropriate acoustics ... so vital to realism and reduced listener fatigue.

 

I have played my system to many well traveled (*) opera lovers who, uninterested in HiFi sets, are enraptured with the realism and musicality that the Sopraninos recreate.
 

Indeed, upon the visit of Enigmacoustics Taiwanese engineers to my music room, one wept when he heard the opening notes of Van Clyburn’s Rachmaninoff.

 

Again, the Sopraninos are not “Tweeters.” [Bruce prefers to refer to them as Ambience enhancers]

Bat Pro2s, however, are tweeters, or more aptly Super Tweeters, and they do something

important but different than Sopraninos.

 

Sincerely, Bruce Bisenz

 

(*) Literally World Travelers intimately familiar with the acoustics of the World’s most famous Opera houses on many continents.

 

 

Later :

 

Mr. Tweeter,

 

The immortal Solti/Culshaw recording of Richard Wagner’s Ring of the Nibelungen from Blue Ray (@ 24 bits 48kHz).

 

There’s not the near/medium field direct impression I had in my bedroom since the throw of the big system is 12’.

 

I have these little suckers [BATPRO2s] running wide open paralleled with the SOPs. The Center mini tweeters are in series so that should/might yield the same level as one unit at 100 dB but with a wider stage.

 

The voices are clearer/smoother. The massed brass is more discrete and the image is larger too. When the orchestra is at full tilt you can hear the flutes punch through it all so very well.

 

Overall, there’s the impression of additional definition but not necessarily just in the extreme highs. This is in some ways analogous to the SOPs but the magic is not done by ambience.

 

Instead, the Sops seem to be synergistically supported by these new tweeters. This is not a massive effect but it is endearing and musical.

 

Certainly a fine product and that after 10’ of listening. Tomorrow I’ll hookup another pair of tiny tweeters to the side SOPs. But it sure won’t get worse that’s for sure.

 

Damn but all the singing voices are just better now! This is, of course, what Opera fiends will kill for. “Leb Wohl” the big finish of Die Walkure. Wotan sings over his beloved Wish Maiden.

 

Can’t turn it off. Hypnotic for the extra musical content in this material that I know so very well.

No question, with the Batpro2 there’s more Wotan there. Waiting for the flutes in the Magic Fire Music.

Finally, the definitive parameter - more defined acoustic space. Whew!
 

Bruce Bisenz

 

 

 

 

PAUL REALE – Composer / California

https://www.gramophone.co.uk/review/paul-reale-cme-presents-piano-celebration-vol-2 ➢ https://www.naxos.com/person/Paul_Reale/58355.htm

https://www.last.fm/music/Paul+Reale/+wiki
https://www.youtube.com/watch v=OF0V8YBCprM&list=OLAK5uy_nGwZfGDzBinaT4jBgOK9I1HqJOO4Bye8U

 

 

Paul’s System Description

  • The two main speakers are Sound Lab M-1 PX's with special backplates (better caps and resistors), driven by custom 600 Watt hybrid amps, built by Stephen Sank.

  • The surround channels are Monitor Audio Golds, powered by a Myriad (British amp).

  • All the electronics are on dedicated, shielded circuits which are controlled by devices ordinarily used to stabilize the power for electron microscopes.

  • The Sound Labs are bolted to the foundation for stability.

  • Preamp is by MBL (not with their terrible phono stage).

  • I am using an old phono stage from Threshold with their special power supply - I still like it.

  • Surround channels are driven by an experimental Audio Research unit, which they decided not to sell to the public

 

 

Paul’s Feedback on Enigmacoustics Sopranino & Taket Barpro2

 

 

Dear Constantin,

 

On the Sopranino :

 

I used some of my own recordings but wound up testing with a DSD recording of Stravinsky's Firebird. The most obvious thing is the increased energy in tricky attack like the pluck of a harp in the orchestra or the first split second when the mallet hit timpani, or any string pizzacatos.

 

The Sops are so fast that this information is just not available on any speakers, including first class electrostatics like my Sound Lab M-1 PX's. I found that the middle setting, and the 0 db setting work best. Where I have read that people use a little toe in, I preferred the SOPs to be straight ahead and about 40" from the floor ... I am certainly glad I purchased these little gems.

 

 

Later comment :

 

From my headphones, the Rubanoides (Paul is referring to my favorite reference speakers) seem to be very clean and honest. I don't know whether they could fill a gigantic listening room like mine (75 ft. long).

 

What is interesting to me in my room is that the Sopraninos are helpful to full range electrostatics and planars.

 

If you would like some CDs of my music, I will send them on, if you give me some kind of address.

(Paul sent me 4 CDs ! ...and I loved these)

 

 

Further listening :

 

Listening to the new setup, I suddenly realized why recorded violins sound harsh. If you don't get the first few milliseconds of the bow on the string ... which is provided by the SOPs ... it is like splicing off the initial parts of the attack. I now really appreciate why adding HF's with the ENIGMAcoustics Sopranino subtracts or eliminates, rather than adds to the harshness ... a very good selling point.

 

I’m thinking now of using two Sopraninos in series on each channel, thus bringing the nominal impedance to 8 ohms and converting what is a point source - perhaps the only shortcoming in the unit- to a line source. At some point I would like to try this.

(And a month later, Paul did just that !)

 

BTW, Good news: Robert Baird of Stereophile has accepted my 2-piano CD for a review.

 

 

Paul orders the second pair of Sopraninos :

 

Dear Constantin,

 

Thanks for your kind words about my music. I have been on a fierce campaign against mainstream modernism and the evanescent novelty that accompanies it.

 

I think that I will take your offer of 15% off for my second pair of SOPs, plus some of your special wire to use as jumpers.

 

As for the TAKET Batpro2's: let me look into this --- maybe at a later time. Placement is so critical with super tweeters, and I would like to get the double pair of SOPs right, first.

 

Interestingly enough, some other dealers, and one in particular who sells Sound Lab, totally pooped on the idea on any super tweeters with them. He has either forgotten - or does not have a clue - about the “incredible speed” of the SOPs.

[This is an example of the “not invented here syndrome”, no doubt. It is what it is]

 

BTW, Below is my recent interview with Fanfare Magazine about Novelty vs. Originality.

http://www.naxos.com/

 

 

Paul & the BATPRO2 Demos :

 

Dear Konstantin,

 

I am happy with using your demos, and will therefore definitely try the Batpros.
 

My reservations: They are probably not fast enough to enhance the Sound Labs already quick response - unlike the SOPs, which are much faster. I will certainly give you my impressions.

 

 

Three days later :

 

My idea of running the SOPs “in series” is working very well. The only thing I had to adjust was to change the crossover point to 8K.

 

The Batpro2s do very little in the front channels, no doubt because of the sheer size of the Soundlab’s radiating area compared to their relatively small one. Multiple BATPROs may change matters. However, I have an idea: I am going to try them in the surround channels.
 

 

And a few days later :

 

I am a great believer in serendipity, probably as a result of a lifetime of creative activity. I remember rehearsing my first good piece, which featured a big soprano solo near the end. In the rehearsal, the soloist came in one measure too soon: the result for the most part was spectacular. I realized that intuitively, the performer knew more about my piece than I did ... I had a similar experience with your TAKET Batpro2’s.

 

The [single pair] of BATPROs did not do much connected with my Sound Labs. Also possibly because they cut in at too high a frequency (18K), and the SOPs don’t do much at the 12K setting, but did at 8K, and there is no beaming, because the SOP pairs act more like a line source.

 

However, I decided to hook the BATs up to my surround channels, which consist of four Monitor Audio Gold surrounds ... and the result was absolutely astonishing.

 

More specifically, I got the surround channels to really sing, using the 90db setting on the Batpro2's and running them parallel to each pair of Monitor Audio Golds.

 

I am glad you sent the BATs to me , because I would have never thought to try them. I would like to buy them - please send me an invoice.

 

 

Paul’s Update :

Even though the Monitor Audio Golds are considered by many to be the best surround speakers, they cannot reproduce that first few milliseconds of attack that make sound lifelike. Also, the same for decays. Assuming the gear is up to it, that part of the sound-wave is critical to the "you are there" illusion.

It never occurred to me to augment my surround channels. Initially, I was using AR 10 PI's in the back, but they were really too directional. The Monitor Audios have adjustments that are critical, but they can't reproduce the essential T1 and T3 components.

 

BTW, there is no problem of beaming with the Batpros, because they are 24 feet behind the listener. [WOW]

 

I thought that I would also update you on my latest observations :

  1.  Every review that I read says that there is no break in time for the Sops.

  2.  From using them for about 100hrs , I would say that those reviewers are wrong.

  3.  The things got really better and sweeter, and I had to change my crossover setting from 8K to 10K.

  4.  Also, I wired the two Sops in series, so the impedance was 8ohms, matching that of the Sound Labs.

  5.  Those dealers who said that I was wrong to try to convert a point source by stacking the Sops were   wrong, themselves. The pair seems to work just as I intended.

  6.  The only kicker is that with my setup, you get an incremental but definite improvement,but

     for almost $9000.

  7.  I think that ENIGMAcoustics should market a bigger supertweeter, the way TAKET did with

     the expensive Batmaster. If ENGIMA could produce a Double-SOP for around $5000, that would be   very good.

AND, in a sense Enigmacoustics did do just that in January 2019. The SOP2 at $3K -- which Atelier 13 Audio has decided to offer customers like Paul at $2,595 / pair !

We will be adding more feedback as we get it

JBL Paragon + TAKET super tweeters

JBL Paragon + TAKET super tweeters

Play Video
SSB 8にPW80+スパーツイーター換装

SSB 8にPW80+スパーツイーター換装

Play Video
BATPRO 2 比較動画 | JBL4307 | Accuphase E-270 | 01:09で切り替えてます

BATPRO 2 比較動画 | JBL4307 | Accuphase E-270 | 01:09で切り替えてます

Play Video
Markaudio Alpair 7 v3 + BATPURE

Markaudio Alpair 7 v3 + BATPURE

Play Video
bottom of page