atelier 13 audio
ELAC MIRACORD 50 TURNTABLE
Smooth Vinyl Precision and the next chapter of our legacy. Designed to deliver the same exceptional listening experience as our whole Miracord Series.

ELAC MIRACORD 50
The warmth of analog sound
The resurgence of vinyl has created a groundswell of enthusiasm among audiophiles and music enthusiasts who have never before enjoyed the thrill of spinning an LP! The Miracord 50 is the perfect choice for those building a new LP collection, or for rediscovering the magic of an existing record library.
ELAC’s Miracord 50 Turntable is designed to deliver exceptional vinyl transcription, inspired by the iconic Miracord name from the Golden Age of Stereo when turntables reigned supreme. The Miracord 50 is carefully engineered with a belt- drive motor and aluminum die cast platter.
A precision static-balanced, straight-tube tonearm with removable head-shell features a factory-mounted MM phono cartridge.
Designed with convenience in mind, the Miracord 50 is equipped with a built-in phono preamplifier, allowing you to add this turntable to any music system.
MAP PRICE $ 349.98
Including Tonearm, Phono Preamplifier & AT95 Cartridge




PRECISION TONEARM & CARTRIDGE
The tonearm is a static-balance, straight- tube design with precision bearings, built- in anti-skate adjustment and removable bayonet-style head-shell.
A pre-mounted moving-magnet cartridge takes all the guesswork out of setup and assures proper vertical tracking angle, tracking weight and azimuth adjustment right out of the box.
ANTI-RESONANT CHASSIS
Superior isolation is achieved with a chassis designed to minimize the sonic e ects of vibration and feedback.
A low-noise DC servo motor drives a die-cast, high-inertia aluminum platter with special record mat via a rubber belt, resulting in stable speed and minimal wow and utter.uperior isolation is achieved with a chassis designed to minimize the sonic effects of vibration and feedback
BUILT-IN PHONO PREAMPLIFIER
Unlike most turntables, the Miracord 50 comes complete with a built-in defeatable phono preamp for correct RIAA equalization.
That means you can add LP playback without having to add a costly phono stage to line-level preamps or digital-only systems. Just plug it in, put on a record and enjoy rich LP sound!



CONTEMPORARY FINISH
Styled to complement any interior, the Miracord 50 is available with a silver chassis and gloss-black plinth.
A hinged, tinted dustcover is included.
ELAC MIRACORD 50 TURNTABLE SPECIFICATIONS
TURNTABLE SECTION
Drive System
Belt drive
Motor
DC motor
Selectable Speeds
331⁄3 and 45 rpm
Rotation Speed Variation
+/-1 %
Wow and Flutter
0.1 %
Signal-to-Noise Ratio
-67 dB or higher (A-weighted)
-60 dB or higher (unweighted)
Platter
Aluminum die cast
Connector
RCA jacks including RCA cable
Voltage
100 to 240 V AC / 50/60 Hz
Power Consumption
1.5 W (less than 0.5 W at standby)
Dimensions (H x W x D)
5.5“ x 16.5“ x 14.2“
140mm x 420mm x 360mm
Weight
12.1 lb / 5.5 kg (approx.)
CARTRIDGE SECTION
Type
Audio-Technica AT91 MM
Frequency Response
20 Hz to 20 kHz
Channel Separation
>18 dB
Channel Balance
2.5 dB
Vertical Tracking Angle
20 degrees
Supported Load Impedance
47 kΩ
Stylus Pressure
2.0 g +/-0.5 g
Cartridge Weight
5.0 g +/-0.5 g
Headshell Weight
11.0 g (incl. screws, nuts & wires)
TONEARM SECTION
Type
Aluminum tube, static-balanced
Stylus Pressure Range
0 to 4.0 g
Cartridge Weight Range
3.5 to 6.0 g
Effective Arm Mass
27.4 g
Overhang
18.6 mm
Offset Angle
25 degrees
Anti-Skating Adjustment
0...4
Main Bearing
Stainless steel
PHONO EQUALIZER AMPLIFIER
Type
Moving magnet (MM)
Phono Output
2.5 mV (1 kHz, 3.54 cm/sec)
Line Output
140 mV (-17 dBV)